黑龙江吊牌SJQ平角圆角切角机质量

圆角封面机的给纸部分由给纸台、输纸头、接纸轮、双张检测装置、输纸台等部件组成，其功能是把纸张准确平稳地输送到上胶部位。机器给纸台板放置在前后三根横档上，堆放纸张时，纸张的中心一般应对准机器的中心，纸张前边缘应靠齐前齐纸板，转动手轮，调节侧挡纸规左右位置靠齐纸堆。电器按钮面板上设有给纸台升降按钮，按此两个按钮，可使纸台快速上升或者下降。（注意：纸堆快速上升时一定要使压脚处于纸堆的后边缘并处于低位置）若您有合作意向，请您为我们留言。黑龙江吊牌SJQ平角圆角切角机质量

Our main product contain the series complete set of equipment for playing card process and manufacture, YMQ series trademark die cutters, SJQ series angle cutter, SWY catalog index digging machine, YYJ series book compaction machine and other paper processing machine for brand, notebook, drop, book and wall calendar etc. The above product is necessary equipments for manufacturers to refine process to paper printing.

Since we establishment in 1985 , our company has felt greatly honoured to be given such support and deep love from customers. In the new century, based on the principle of “practice, innovation, exploitation and progress”, we must win victory with our high quality and thrive business with our brand. It’s our permanent goal is to provide more excellent and perfect equipment and service for customers and it’s our obligation to create high effect equipment for everybody. Cooperation hand in hand and creating the brilliance together are our undeviating faith.

北京不干胶SJQ平角圆角切角机品牌排行产品远销了多个地区。

对设备的操作一定要严格按照规定进行，下面小编就为大家简述精密钢板剪切机安全操作注意事项。很多用户在购买精密钢板剪切机时并不知道如何正确的操作，没关系下面小编就来教大家如何作。希望小编的回答对大家有所帮助，首先当我们在熟悉操作精密钢板剪切机安全操作前，四周应有足够的钢筋堆放场地，转动部件要有防护罩，须检查刀片有无裂纹，刀片固定螺丝是否紧固。不准用两手分别握住钢筋的两端剪切，只准用手握住靠身边一端的钢筋上，综上所述相信不用小编多说，大家也应该能够了解了，液压圆钢切断机的使用方法。切断机是生产加工必不可少的设备之一。 

SJQ-120A机器由机座、机头、减速箱、工作台、切角刀、拖板等零部件组成。电机通过减速箱减速后，带动飞轮旋转，当扳下操作手柄或踩下踏板时，开关座即与飞轮啮合，从而使偏心轮转动，再通过连杆带动切角刀作上下裁切运动。

当您在收到我们的机器后，首先应检查机器是否完好无损。然后再安装机器。并且安装底脚螺丝固定位置尺寸，或者也可以不装

机器置于水泥地上，比较好在机器底座下垫以布垫。以免使用过程中机器移动位置。

SJQ-120A机器的参数如下，您可自行与您的要裁切的产品作参考。 若需要更大的台平，请来电咨询。

试车Test run在机器安装好后，在接通电源试车，试车前应将各注油孔、滑动面、，注入润滑油，开机前用手扳动偏心轮(图(2)中3)，使切刀做一、两次循环运动，检查机器是否正常，电机转动方向应与偏心轮上箭头所指方向相同，否则裁切时会导致机器非正常损坏。可打开机器左侧小门，观察飞轮转向（图（2）中11）是否与偏心轮上箭头所指方向一致。

After the machine is installed, before the power supply test is connected, each injection hole, sliding surface, and lubricating oil should be injected before the test, and the eccentric wheel should be pulled by hand before starting(Figure(2) in 3). Make the cutter do one or two cycles of movement, check whether the machine is normal, the direction of motor rotation should be the same as the direction indicated by the arrow on the center wheel, otherwise the cutting will cause abnormal damage to the machine. The small door on the left side of the machine can be opened to see whether the flywheel steering(11 in Figure(2)) is consistent with the direction indicated by the arrow on the center wheel. 一级制造商,生产,售后,品质服务20年。安徽名片SJQ平角圆角切角机设备制造

为客户创造价值，与客户共创未来。黑龙江吊牌SJQ平角圆角切角机质量

Δ注意事项matters needing attention:

一、 工作期间注意力集中，严格遵守设备操作规程，做到安全作业。

二，调整设备前首先切断电源。

三、根据产品规格的尺寸要求，进行精确调整，调整时需使用**工具，小心仔细，注意安全。

First, pay attention during the work, strictly observe the equipment operating rules, to achieve safe operations.

Second, cut off the power before adjusting the equipment.

Third, according to the size requirements of the product specifications, make precise adjustments. When adjusting, use special tools, be careful and pay attention to safety. 黑龙江吊牌SJQ平角圆角切角机质量

温州市旭日印刷机械有限公司位于梧田镇辉煌路9号。旭日印刷机械致力于为客户提供良好的冲切抹角机，切角机，挖月机，压紧机，一切以用户需求为中心，深受广大客户的欢迎。公司从事机械及行业设备多年，有着创新的设计、强大的技术，还有一批**的专业化的队伍，确保为客户提供良好的产品及服务。旭日印刷机械秉承“客户为尊、服务为荣、创意为先、技术为实”的经营理念，全力打造公司的重点竞争力。